DCS WD-30-BL Technical Information Page 118
- Page / 310
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Configuration
Tsunami
®
8000 Series - Software Management Guide 118
WORP Configuration page (See Wireless Outdoor Router Protocol (WORP)).
To configure the RADIUS Server profile, navigate to ADVANCED CONFIGURATION > Security > RADIUS. The following
RADIUS Server Profile screen appears:
Figure 5-54 Configuring RADIUS Server Profile
Given below is the table which explains RADIUS Server parameters and the method to configure the configurable
parameter(s):
Parameter Description
Profile Name A name that represents the Radius Server profile. By default, it is Default Radius.
Max Retransmissions Represents the maximum number of times an authentication request may be retransmitted
to the configured RADIUS server. The range is 0 to 3. By default, it is set to 3.
Message Response
Time
Represents the response time (in seconds) for which that the BSU/End Point A should wait
for the RADIUS server to respond to a request. The range is 3 to 9 seconds. By default, it is
set to 3 seconds.
Re Authentication
Period
Represents the time period after which the RADIUS server should re-authenticate an SU or
an End Point B. The re-authenticate period ranges from 900 to 65535 seconds. By default,
the re-authentication period is set to 0.
Entry status A read-only parameter which displays the status of the RADIUS server profile as enabled.
The Entry status cannot be disabled or edited.
Server Type For better accessibility and reliability, you can configure two RADIUS servers:
1. Primary RADIUS Server
2. Secondary RADIUS Server
The secondary RADIUS server serves as backup when the primary RADIUS server is down or
not reachable.
- 8000 Series 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- GPL License Note 2
- OpenSSL License Note 2
- Contents 3
- About this Guide 8
- Products Covered 8
- Audience 9
- Prerequisites 9
- Related Documents 9
- Documentation Conventions 9
- Overview 11
- 1.2 Wireless Network Topology 14
- 1.2.2 Point-to-Point Link 18
- 2.2 Command Line Interface 22
- 2.3 SNMP Management 23
- 2.4 ProximVision NMS 24
- Device Initialization 25
- 3.2.1 Home Page 29
- 3.2.2 COMMIT 30
- 3.2.3 REBOOT 31
- Basic Configuration 34
- 5.2 Network 44
- 5.2.2 Static Route Table 56
- 5.2.4 RIP 60
- 5.2.6 IP over IP Tunneling 67
- 5.3 Ethernet 71
- 5.3.2 Advanced Configuration 73
- 5.4 Wireless 74
- should be same 85
- Advanced Configuration 101
- 5.4.5 Roaming 104
- < (New BSU Rx SNR) then 110
- value ranging from0-10 110
- 5.4.6 BSU / SU Profiles 111
- 5.5 Security 114
- 5.5.2 RADIUS 117
- 5.5.3 MAC ACL 119
- 5.6 Quality of Service (QoS) 121
- 5.6.2 QoS Configuration 127
- Figure 5-64 QoS PIR Add Entry 132
- 5.8 VLAN (Bridge Mode Only) 151
- 5.10 Filtering (Bridge Only) 160
- 5.10.1 Protocol Filter 161
- Figure 5-94 Protocol Filter 162
- 5.10.3 Advanced Filtering 167
- 5.10.4 TCP/UDP Port Filter 169
- 5.10.5 Storm Threshold Filter 171
- 5.11 DHCP 177
- 5.11.2 DHCP Server 178
- 5.12 IGMP Snooping 182
- Management 184
- 6.1.2 Inventory Management 185
- 6.1.3 Licensed Features 186
- 6.2 File Management 187
- 6.2.3 Upgrade Firmware 190
- 6.2.4 Upgrade Configuration 192
- 6.2.5 Retrieve From Device 194
- 6.3 Services 198
- 6.3.2 Telnet/SSH 199
- 6.3.3 SNMP 201
- 6.3.4 Logs 204
- 6.5 Access Control 209
- 6.6 Reset to Factory 210
- 6.7 Convert QB to MP 210
- 7.1 Interface Statistics 212
- 7.1.2 Wireless Statistics 214
- 7.1.3 PPPoE Statistics 215
- 7.1.4 IP Tunnels 217
- 7.2 WORP Statistics 218
- 7.2.2 Link Statistics 222
- 7.3 Active VLAN 227
- 7.4 Bridge 228
- 7.4.2 Learn Table 229
- 7.5 Network Layer 230
- 7.5.3 ICMP Statistics 231
- 7.5.4 IP Address Table 232
- 7.5.5 DNS Addresses 232
- 7.5.6 Neighbour Table 233
- 7.5.7 RIP Database 233
- 7.7 IGMP 235
- 7.7.2 Router Port List 236
- 7.8 DHCP 237
- 7.9 Logs 237
- 7.9.2 Debug Log 238
- 7.9.3 Temperature Log 239
- 7.10 Tools 242
- 7.10.2 Scan Tool 243
- 7.10.3 sFlow® 243
- 7.10.4 Console Commands 247
- 7.10.5 Spectrum Analyzer 248
- Graph Results Interpretation 250
- 7.11 SNMP v3 Statistics 252
- Troubleshooting 253
- 8.1 PoE Injector 254
- 8.2 Connectivity Issues 255
- 8.6 Wireless Link Issues 259
- 8.9 Recovery Procedures 263
- 8.9.2 Bootloader Mode 265
- 8.9.3 Load a New Image 265
- 8.10 Spectrum Analyzer 269
- 8.11 Miscellaneous 269
- Feature Applicability 270
- Parameters Requiring Reboot 272
- BSU: Refers to a Base Station 275
- Introduction 276
- Point to Multipoint Devices 277
- Point to Point Devices 278
- 2.4 GHz Channels 279
- 4.9 and 5 GHz Channels 280
- ranging from 286
- LACP - Device Management 288
- Example2 289
- Bootloader CLI and ScanTool 292
- ScanTool 293
- SNR Information 294
- • MP-8150-CPE 296
- • QB-8150-LNK-12/50 296
- • MP-8200-BSU / SUA 299
- • MP-8250-BS9 / BS1 299
- • MP-8250-SUR 299
- Abbreviations 300
- Lightning Protection 304
- Statement of Warranty 305
- Other Information 306
- Support Options 307
- Telephone Support 308
- ServPak Support 308
- Packaged Services 308
- Technical Support Policy 309
Related products and manuals for Warming drawers DCS WD-30-BL
Warming drawers DCS WD-30-BL Specifications
(238 pages)
(238 pages)
Warming drawers DCS WDU models Specifications
(318 pages)
(318 pages)
Warming drawers DCS WDUI models User's Guide
(40 pages)
(40 pages)
Warming drawers DCS WDU models User's Guide
(78 pages)
(78 pages)
Warming drawers DCS DCSWD27SSOD Manual
(44 pages)
(44 pages)
Warming drawers DCS WD130-SSOD User Manual
(40 pages)
(40 pages)
Warming drawers DCS WDVI30 User Manual
(40 pages)
(40 pages)
Warming drawers DCS WDVI30 User Manual
(40 pages)
(40 pages)
© 2020, manymanuals.com. All rights reserved. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals